"A Complete Top-to-Bottom Pool Cleaning Solution"
Simplify your pool care with the Aiper Scuba S1 Cordless Robotic Pool Cleaner & Surfer S2 Solar Power Cordless Pool Skimmer Bundle. This dynamic duo combines the Scuba S1’s powerful underwater cleaning—covering floors, walls, and waterlines—with the Surfer S2’s solar-powered surface skimming, ensuring your pool stays spotless from top to bottom with minimal effort.
Aiper Scuba S1: Deep Cleaning Power
The Aiper Scuba S1 excels at cleaning your pool’s floors, walls, and waterline. Equipped with caterpillar treads for enhanced traction, it climbs sloped walls up to 105° – outperforming wheel-based cleaners. Designed for both above-ground and in-ground pools up to 150 m², the Scuba S1 uses a brushless drain motor and filters up to 265 LPM, capturing dirt and debris with its dynamic silicone brush. With WavePath Navigation 2.0 and four cleaning modes (Auto, Floor, Wall, and Eco), it ensures thorough, efficient coverage every time. Learn More
Aiper Surfer S2: Solar-Powered Surface Mastery
The Aiper Surfer S2 keeps your pool’s surface clear around the clock. Solar-powered skimming and a long-lasting battery enable continuous skimming, while a 150 µm fine filter and wide 22.7 cm inlet capture everything from dust and pollen to larger leaves. Control start/stop, steering and schedules in the app, and use the built-in chlorine dispenser (accepts tablets up to Ø76 × 25 mm) to keep residuals steady as it skims. With dual optical (dToF) sensors, DebrisGuard leak-proof baffle, and self-rescue anti-stranding design, S2 delivers cleaner water with fewer interventions. Learn More
Aiper Scuba S1 Key Features
- Caterpillar treads for superior traction and mobility
- Wall-climbing capability up to 105°
- WavePath Navigation 2.0 for intelligent cleaning paths
- Four cleaning modes: Auto, Floor, Wall, and Eco
- 265 LPM suction with brushless motor
- Top-load 3.5L filter basket, 180μm fine filtration
- 150-minute battery life, 3-4 hour charge
Aiper Surfer S2 Key Features
- Solar-powered with 24/7 operation via solar top-ups
- Adapter/DC charging with up to 35-hour runtime
- Dual optical (dToF) sensors for obstacle avoidance
- App support for manual control and monitoring
- 4 L debris basket with 150 µm fine filter
- Brushless motor with paddle-wheel design
- UV-resistant body and salt-chlorine tolerant components
Why This Bundle?
Together, the Scuba S1 and Surfer S2 provide a comprehensive cleaning system. While the Scuba S1 dives deep to scrub and filter below the surface, the Surfer S2 keeps the top pristine, preventing surface debris from ever reaching the bottom. Both are cordless, easy to use, and built for durability, with replaceable accessories and user-friendly features like quick water release (Scuba S1) and a side-drawer debris basket (Surfer S2). Compatible with various pool shapes and surfaces, this bundle is perfect for pool owners seeking convenience and efficiency.
- Complete Pool Care: Cleans from surface to floor, ensuring no spot is missed.
- Time-Saving Efficiency: Scuba S1’s smart navigation and Surfer S2’s app control reduce manual effort.
- Eco-Friendly Operation: Surfer S2’s solar power and Scuba S1’s energy-efficient motor lower your environmental footprint.
- Long-Lasting Performance: Durable designs with replaceable parts extend product life.
- Wide Pool Compatibility: Works with various pool types, shapes, and surfaces for maximum flexibility.
Technical Specifications
| |
Aiper Scuba S1 |
Aiper Surfer S2 |
| Pool Type |
In-ground & Above-ground |
All types (except infinity/glass) |
| Coverage |
150 m² (1600 sq. ft.) |
Surface cleaning, any size |
| Cleaning Focus |
Floor, Walls, Waterline |
Surface (leaves, debris, insects) |
| Power |
Battery (up to 150 min) |
Solar + DC (up to 35 hours) |
| Charging Time |
3-4 hours |
4.5 hours (DC) |
| Technology |
WavePath Navigation 2.0 |
Optical (dToF) Sensors, App Support |
In the Box
- 1 x Aiper Scuba S1with 180 µm Fine Filter Basket
- 1 x DC Charger
- 1 x Retrieval Hook
- 1 x FAQ Card
- 1 x User Manual
- 1 × Aiper Surfer S2 with 150 µm Fine Filter Basket
- 1 × DC Charger
- 1 × User Manual
- 1 × Foam Noodle
- 1 × Quick Start Guide
Frequently Asked Questions
Can I run Scuba S1 and Surfer S2 at the same time?
Yes. Scuba S1 cleans the floor, walls, and waterline while Surfer S2 skims the surface. Both are cordless and operate independently, so they won’t interfere with each other.
How does Surfer S2 help Scuba S1’s results?
Surfer S2 removes leaves, insects, pollen and dust before they sink, so Scuba S1 has less to pick up on the floor and walls. That supports clearer water between deep cleans.
What are the runtimes and charging times?
Scuba S1 runs up to 150 minutes and typically recharges in 3–4 hours. Surfer S2 can skim continuously with solar top-ups and delivers up to 35 hours of operation from a full DC charge (about 4–6 hours to recharge).
Which pools is the bundle suitable for?
Scuba S1: in-ground and above-ground pools up to 150 m²; cleans floor, walls, and waterline. Surfer S2: most pool shapes and finishes; not suitable for infinity/zero-edge pools. Recommended water: 10–40 °C, pH 7.0–7.8, chlorine ≤ 4 ppm, salt ≤ 5000 ppm.
How does Scuba S1 handle walls and coverage?
Caterpillar treads boost traction, allowing Scuba S1 to climb sloped walls up to 105° (≈90° ± 15°). WavePath™ 2.0 navigation plans efficient routes, and four modes (Auto, Floor, Wall, Eco) match different cleaning needs.
How does Surfer S2 avoid obstacles and getting stuck?
Two dToF optical sensors detect walls, ladders, and edges early and adjust course. A self-rescue algorithm and adjustable anti-stranding columns help it free itself if it catches on steps or shallow areas.
What happens if the Surfer S2 gets stuck?
A self-rescue algorithm and adjustable anti-stranding columns help it free itself. You can also steer it via the app. If it catches at the pool’s built-in skimmer, place the included foam noodle at the skimmer mouth and reduce that suction while the S2 is running. Avoid running other cleaners at the same time.
Tips to Prevent Your Skimmer Robot from Getting Stuck with a Fixed Skimmer Entrance
- Foam noodle included.
- Location: box or filter basket.
- Remove if in basket → avoid roller brush jam.
- Place in skimmer port → avoid getting stuck.
Maintenance tips for best performance
After each session, empty and rinse the Surfer S2’s 4 L basket and clean its 150 µm filter. For Scuba S1, rinse the top-load 3.5 L basket and keep the pool chemistry balanced. Do not leave Scuba S1 in the pool when not in use; allow both units to dry before storage.
Troubleshooting quick checks
Surfer S2: If it backs up or isn’t avoiding obstacles, clean the optical sensor lenses and power cycle; check app notices. If it spins in circles, inspect the propeller/impeller for debris and clean the lenses. If it won’t turn on/charge, ensure the port is dry, confirm the charger LED, operate within 10–40 °C, and recharge fully (4–6 h). Scuba S1: If performance drops, clean the filter basket and consider Eco/Auto modes for regular upkeep.
Note!
Differences between Product Illustrations and Actual Products: The product illustrations (including product pictures, images and display contents) displayed on the website are for reference and illustrative purpose only. The actual products received by each customer may vary and differ slightly with the product illustrations in the aspects including but not limited to appearance, color, logo, dimension and size due to production batches, improvements, legal and regulatory requirements, country or region or other reasons. Please refer to the actual products received. The final interpretation of product specifications and appearance belongs to Aiper.
